VIVAnews Forums
Welcome to VIVAforum!
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 24 July 2012, 13:47
handy01's Avatar
Banned
 
Join Date: Jun 2012
Location: 20
Posts: 521
Thanks: 0
Thanked 0 Times in 0 Posts
handy01 is an unknown quantity at this point
Default Motor Elektrik Dijual dengan harga murah

Motor Elektrik Dijual dengan harga murah

Harga Masih Nego : USD 500



Deskripsi : <Strong>Premium Efficient</Strong>
Super-E Motors Are Designed To Conserve Energy Over Extended Time Periods. These Premium Efficiency Designs Are Available In Both Totally Enclosed Fan Cooled And Open Drip Proof Construction. All Three Phase Motors Are Inverter Ready Per Nema Standard Mg1, Part 31.4.4.2. This Means The Motors In 230 And 460 Volts Meet Nema'S Corona Inception Voltage Requirements, Under This Standard, And Can Withstand Peak Voltages Of Up To 1600 Volts. Motors Having Premium Efficiency Are Also Available In Single Phase Designs.

<Strong>Single Phase</Strong>
In Applications Where Only Single Phase Power Is Utilized, These Motors Are Available From 1/12 Hp Through 15 Hp In Tefc And Odp Designs. Standard Foot Mounted Configurations Are Available, As Well As C-Face Foot Mounted And C-Face Footless. These Are Also Offered In 1/4 Hp Through 5 Hp As Super-E&Reg; Premium Efficient Motors Where Energy Savings Is Desired.

<Strong>General Purpose</Strong>
Baldor'S Extensive Line Of General Purpose Motors Are Available In Open Drip-Proof And Tefc Construction In Both Single And Three Phase. Horsepower Sizes Available From Stock Range From 1/12 Hp Through 1500 Hp. Designed For &Quot;General Purpose&Quot; Use Means That These Motors Can Be Used In Applications Which Include Compressors, Pumps, Fans, Conveyors, Material Handling, Machine Tools And Many Others.

<Strong>Severe Duty</Strong>
Severe Duty Motors Are Available From 1 Hp To 700 Hp. These Products Are Especially Designed For Those Applications Requiring Protection Of The Motors From Severe Environmental Operating Conditions. A Few Typical Applications Which Might Require These Types Of Motors Include Petro-Chemical Plants, Mines, Foundries, Pulp And Paper Plants, Waste Management Facilities, Rock Crushers, And Chemical Plants.

<Strong>Washdown</Strong>
Baldor'S Washdown Duty Motors Are Available From Stock In Single And Three Phase Ac And In Dc Designs. Horsepowers Range From 1/2 To 20. Designs Include Motors Having An Electostatically Applied Epoxy Finish, Paint Free With Major Components In 300 Series Stainless Steel, And All Stainless Steel. Applications Include Food Processing, Packaging, Pharmaceuticals, Or Applications Where Motors Are Regularly Exposed To High Pressure Wash Down.

<Strong>Explosion Proof</Strong>
Baldor'S Explosion-Proof Motors Are Ideal For A Wide Variety Of Applications Where Hazardous Fumes Or Dust May Be Present. The Motors Are Available In Three Phase And Single Phase With Ratings, In Stock, From 1/4 Hp Through 300 Hp. Designs Available Include Standard Foot Mounted, C Face With Base And C Face Less Base, 60 Hz And 50 Hz, Jet Pump Motors, And Inverter Drive Motors.

<Strong>Pump</Strong>
Our Pump Line Of Motors Includes Single Or Three Phase Jet Pump Motors, Square Flange Motors, Close-Coupled Pump Motors, And P-Base Vertical Solid Shaft Pump Motors. The Motors Are Stocked In Totally Enclosed Fan Cooled, Open Drip Proof, And Many Explosion Proof Ratings. Applications For These Run The Gamut From Swimming Pool Pumps To Medium And High Thrust In-Line Pumps Used In Water Treatment Plants. Horse Powers Range In Size From 1/3 Through 75 Hp.

<Strong>Light Industrial / Commercial</Strong>
Baldor'S New Light Industrial / Commercial Motor Line Offers Many Ratings Designed For Applications With Low To Medium Starting Torque Requirements. The Baldor Light Industrial / Commercial Motor Line Brings Baldor'S Reputation For High Quality Designs To Commercial Applications With A Cost-Effective Offering. This Definite Purpose Product Line Is Designed For Certain Applications Requiring Nema 48 And 56 Motors Rated Between 1/4 And 1 1/2 Hp, In Both Single And Three Phase Ratings. Typical Applications Include: Jet Pump, Heating And Cooling, Ventilation, Air Conditioning, Blowers, Direct Drive Fans, Condenser Fans, And Pedestal Fans.

<Strong>Hvac</Strong>
Baldor'S Line Of Heating, Ventilation, And Air Conditioning Motors Are Designed With Dynamically Balanced Rotors For Reduced Vibration And Quiet Operation. The Motors Range In Size From 1/4 Hp To 100 Hp And Include Heavy Duty Industrial Designs As Well As Designs For Commercial Applications. These Applications Include Ventilators, Direct Drive And Belted Fans, Exhaust Fans, Unit Heaters, Air Conditioning Units, And Commercial Refrigeration Condensers. Also Included Are Motors Designed Especially For Use With Variable Torque Electronic Controls That Are Used To Conserve Electricity.

<Strong>Farm Duty</Strong>
These Motors Are Designed For Many Of The Varied Applications Found On The Farm. Designs Include Motors Suitable For Aeration Fans, Auger Drives, Grain Stirring, Metering Pumps, Instant Reversing, Irrigation Tower Drives, And Crop Driers. General Purpose Motors Are Also Available In Both Single And Three Phase, Tefc And Odp Construction. For Those Loads That Are Hard To Start And Require Extra Torque, Baldor Is The Only Motor Manufacturer That Stocks Repulsion-Start Induction Run Motors, In Sizes From 2 Hp To 10 Hp.

<Strong>Definite Purpose</Strong>
The Definite Purpose Family Of Motors Captures A Host Of Variety Demanded By The Marketplace. These Motors Include Tefc And Odp Two-Speed Motors, As Well As Single Phase Pressure Washer Motors. This Group Of Specialty Motors Includes Arbor Saw To Woodworking, Pre-1952 Nema Motors To Sae Hydraulic Pump Motors. An Extensive Line Of Tefc And Odp F-2 Motors Are Available As Well In 1 Hp Through 60 Hp. The Automotive Approved Motors, Approved By Major Us Automobile Manufacturers, Are Available In Cast Iron Designs And Meet All Requirements For Sound Power Levels. A Broad Line Of Design D Oil Field Pump Motors, Requiring High Torque And High Slip, Are Available In 3 Hp Through 150 Hp.

<Strong>Unit Handling</Strong>
Baldor&Rsquo;S Line Of Unit Handling Motors Are Designed For A Wide Variety Of Applications In Baggage Handling, Conveyors, Packaging Equipment, Machine Tools, Hoists, Elevators And Door Openers. These Motors Are Available From Stock In Ratings Of &Frac12; Hp Thru 10Hp (56 Thru 215T Frames) With Or Without Dodge D-Series Brakes. Features Include An Oversized Top Mounted Conduit Box On 56 &Amp; 140T Frames That Provide Easy Access For Making Connections. Footed Frames Include Slotted Feet For Easy Mounting.

<Strong>Brake</Strong>
Baldor'S Line Of Brake Motors Are Available In Totally Enclosed Fan Cooled, Open Drip Proof, Or Explosion Proof Designs, In Either Single Or Three Phase. Stock Ratings Are Available From 1/4 Hp Through 30 Hp. These Motors Use A Mechanical Spring Set Brake With A Manual Release. Brake Motors May Be Used On Machine Tools, Conveyors, Door Operators, Speed Reducers, Hoists, Or Any Application Requiring Quick Stops And Positive Holds.

<Strong>200 &Amp; 575 Volt</Strong>
Some General Purpose Applications Require A Motor That Runs On 200 Volt Power. These 200 Volt Motors Are Stocked From 1 Hp To 50 Hp In Tefc, And 1 Hp To 100 Hp In Odp. Also Available Is An Extensive Line Of 575 Volt Motors. The 575 Volt Motors Are Available In General Purpose Tefc And Odp, Washdown, Severe Duty, Ieee-841, Explosion Proof, And Close-Coupled Pump Designs, In A Variety Of Mounting Configurations.

<Strong>Iec Frame</Strong>
Baldor&Rsquo;S Line Of Iec Frame Motors Are Available From D63 Through D315m, Stocked In 50 Hz Or 60 Hz. This Means That Replacement 60 Hz Motors Are Readily Available From Baldor To Replace Metric Motors That Have Failed On Imported Machinery. Motor Construction Meets Ip54 And Includes Motors With B3 Base Mounting, B5 Flange Mounting, Or B14 Face Mounting. Stock Motors Range In Size From .18 Kw To 132 Kw. Typical Applications For This Product Include Pumps, Fans, Conveyors, Machine Tools, Gear Reducers And Any Other Jobs That Require Iec Frames.

<Strong>50 Hertz</Strong>
Some Applications Require Nema Motors Which Operate On True 50 Hz Power. Where This 50 Hz Power Is All That Is Available, These Nema Motors Are Designed To Be Used At Rated Voltages With Tolerance Of &Plusmn; 15% On Voltage.

<Strong>Inverter / Vector</Strong>
Inverter/Vector Motors Are Equipped With A Superior Insulation System Designed To Comply With Nema Mg-1 Part 31 For Inverter Power. The Motors Available From Stock Range From 1/3 Hp To 1000 Hp. Designed For A Variety Of Industrial Applications Where Full Torque Is Needed From Base Speed Down To Zero Speed. Applications Include Conveyors, Pumps, Fans, Metal Processing, Compressors, Test Stands, Material Handling, Packaging Equipment, Printing Presses, And Others Requiring Exact Speeds And Positioning.

Untuk info lebih lanjut Klik link ini Motor Elektrik

Untuk Produk lainnya , anda boleh klik link dibawah ini
Supplier Alat Alat Mesin Indonesia

Situs Dagang Indonesia
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT +7. The time now is 06:41.